![]() ![]() You can fix it today but it might get stuck again, so it’s better to get it replaced or repaired by a reliable locksmith.Ĭontact us for all your residential and commercial lock and key predicaments in Georgia. However, once a deadbolt starts malfunctioning it’s a sign that it needs replacement. This will make the deadbolt slide back into its slot more seamlessly than before. If the problem still persists, file down the inner strike plate with a metal file to loosen it up a little. Lock and unlock the deadbolt a few times to see if it’s back to working properly. Test it out while the door is still open. ![]() Hopefully, by this point your stuck deadbolt has been unlocked. Screw the lock back in place and try unlocking it again. Place the rod in its allotted area and slide it back. Once it’s come off the door surface, examine the inner deadbolt rod to find out if it’s properly lined up with the slot inside the lock. This will loosen the screws and they’ll come out easier. If the lock is screwed in tight, tap on it multiple times with the back of a screwdriver. Unscrew the bolts on the sides of the lock. If necessary, replace the key or try using a spare. You might need to detach the lock from the door’s surface completely. If your deadbolt won’t turn at all, check the key to make sure it’s not damaged or worn out. This might take a while as it’ll take the parts time to fall back into place and work to open the lock. Twist the key back and forth as you tap on the lock with your hammer. Take a small hammer to the body surrounding the keyhole. Sometimes the lock is stuck because the parts inside it have disengaged. This would do the trick if the jam is caused due to rust or corrosion. Use a graphite spray to grease the key passage, insert your key again and twist it around. Whatever the source, a stuck deadbolt can be fixed in a number of ways: Grease It Up There could also be a mechanical error with the parts within the lock which may be causing the jam. It might get jammed in the strike plate if the key isn’t aligned accurately. One of the most common faults with deadbolt locks that can occur over time is getting stuck in a locked position.ĭeadbolts can get stuck for a number of reasons. However, durable as they may be, deadbolt locks can also malfunction. A local Nest Pro can diagnose what’s causing the problem and fix it for you.A deadbolt lock is the preferred locking system in most households, as it’s more durable than a regular door lock or latch. If you’re having trouble with a misaligned lock, you don’t have to figure it out on your own. You might need to adjust the position of the strike plate on the doorframe so that it’s perfectly aligned with the deadbolt as it extends.Align the turn piece with the torque blade and reinstall the interior assembly on the door. Rotate the turn piece 180° clockwise (you will need to use force when rotating it, and you will hear it click). ![]() This will give the bolt more room to extend. The extended deadbolt lock was hitting the back of the drilled frame, So when it locked, it did not fully extend. You might need to remove the strike plate from your doorframe and chisel more space into the hole for the bolt.From inside your home, close your door and try using the Nest app to lock it. Step 1 - Check the Set Screws First, grasp the inner and outer cylinders of the deadbolt lock and see if they move slightly or wobble.Use the thumb turn to extend and retract the bolt several times. ![]() With the bolt still extended, spray a graphite lubricant on it.Slowly use the thumb turn inside your home to extend the deadbolt all the way to the locked position, then retract it back to the unlocked position. Here are some troubleshooting steps to try: Open your door. Be sure to remove any build-up that may have accumulated. Without accurate calibration, the Nest app may say that your door’s locked when it’s not, or vice versa. With the door open, extend the deadbolt and clean it thoroughly.If there’s any friction, or if you need to push or pull on the door to get the lock to fully engage, it’s a good sign your deadbolt is misaligned. Gently close your door and use the thumb turn inside your home to lock it.Over time, the deadbolt may acquire a build-up of dirt, dust, or other material that slightly changes its size enough to prevent it from perfectly aligning with the strike plate any more. This can cause just enough misalignment to prevent the lock from being able to work on its own any more. If the deadbolt on your door isn’t perfectly aligned with the strike plate on your doorframe, your lock may not be able to lock itself.Įven if you installed the lock perfectly when you first got it, the door and the frame can shift over time, or they can shrink and swell in different weather conditions. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |